Brand New
Pairs (2 pcs) of LED Load Resistor Kit

If you’ve replaced the regular indicator or tail light bulbs on your car with brighter LED bulbs, you may find the new bulbs are either flashing too quickly or are blowing.

Regular bulbs have less resistance than LED bulbs so the simple way to solve these problems is by fitting a resistor parallel to each side (2 bulbs).

The resistor needs to be wired to the ground and turn/tail wires of each side and once installed will:
Correct too-fast flashing
Stop bulbs blowing
Turn Signal Fix
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing, no flashing or burnt out bulb indications. One resistor is required for each turn signal bulb. Includes gel filled moisture resistant splice taps.

Installation Instructions:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake wire. You don't have to cut your car's wiring. Squeeze slice taps with pliers. One Load Resistor required for each turn signal bulb.

Kit Includes:
1 Pairs of (2 prewired Resistors(6Ohm, 50W), and 4 Slice Taps)

Brand New
2 Pairs (4 pcs) of LED Load Resistor Kit

If you’ve replaced the regular indicator or tail light bulbs on your car with brighter LED bulbs, you may find the new bulbs are either flashing too quickly or are blowing.

Regular bulbs have less resistance than LED bulbs so the simple way to solve these problems is by fitting a resistor parallel to each side (2 bulbs).

The resistor needs to be wired to the ground and turn/tail wires of each side and once installed will:
Correct too-fast flashing
Stop bulbs blowing
Turn Signal Fix
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing, no flashing or burnt out bulb indications. One resistor is required for each turn signal bulb. Includes gel filled moisture resistant splice taps.

Installation Instructions:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake wire. You don't have to cut your car's wiring. Squeeze slice taps with pliers. One Load Resistor required for each turn signal bulb.

Kit Includes:
2 Pairs of (2 prewired Resistors(6Ohm, 50W), and 4 Slice Taps)

Brand New
2 Pairs (4 pcs) of LED Load Resistor Kit

If you’ve replaced the regular indicator or tail light bulbs on your car with brighter LED bulbs, you may find the new bulbs are either flashing too quickly or are blowing.

Regular bulbs have less resistance than LED bulbs so the simple way to solve these problems is by fitting a resistor parallel to each side (2 bulbs).

The resistor needs to be wired to the ground and turn/tail wires of each side and once installed will:
Correct too-fast flashing
Stop bulbs blowing
Turn Signal Fix
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing, no flashing or burnt out bulb indications. One resistor is required for each turn signal bulb. Includes gel filled moisture resistant splice taps.

Installation Instructions:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake wire. You don't have to cut your car's wiring. Squeeze slice taps with pliers. One Load Resistor required for each turn signal bulb.

Kit Includes:
2 Pairs of (2 prewired Resistors(6Ohm, 50W), and 4 Slice Taps)

Testimonial:

I install the light into my truck; however, it flashed on and off repeatedly. So I call hidlightsusa.com.
They offer me the load resistor, the problem solve on my new truck

Please check this link http://www.hidlightsusa.com/Bulb%20Check.asp to see if the bulbs fit your car if you are not sure and can't find it on your car's manual.