1 QTY: Somfy Universal RTS Receiver Control (For 110V AC Motors) MPN# 1810627

Amazing Drapery HardwareUniversal RTS Receiver Control (For 110V AC Motor)The SOMFY Universal Receiver provides RTS capability to Somfy’s standardmotors. It can be used stand-alone as a radio control or with Somfy’s RTS sensors for sun and wind control. Used with the Eolis Sensor RTS, wireless wind protection of a retractable awning is possible. If sun protection is also desired, simply use the Soliris Sensor RTS. Two user-defined intermediate positions can be programmed. This control is packaged in a weatherproof enclosure and includes watertight strain-relief fittings for wires entering the box.The receiver can memorize up to 12 different transmitters or channels and up to 3 different sensors.Main technical information:Application(s):•Retractable AwningsRadio Frequency:• 433,42 MHzNominal Voltage / Frequency:• 120V 50/60HzElectrical:Output type of contact:• 115V 5AMinimum voltage:• 180 VMaximum Voltage:• 132 VNominal Voltage / Frequency:• 120V 50/60HzDimension:Weight:• .3 lbTechnology:Radio Frequency: • 433,42 MHz Other:Working temperature: • 4 to 140 °F Visit My eCRATER Store Amazing Drapery Hardware WORRIED THESE ARE RIGHT FOR YOU?NO PROBLEM! We accept returns on all our parts within 14 daysCONTACT USWe are also here to help you through your ordering process.We are still here to help with any questions you may have about your installation once you receive your parts and get to work. QUESTIONS??? EMAIL USWe have years of window treatment experience, WE CAN HELP!UNIVERSAL RECEIVER RTSDESCRIPTION The SOMFY Universal Receiver provides RTS capability to Somfy’s standard motors. It can be used stand-alone as a radio control, or with Somfy’s RTS sensors for sun and wind control. Used with the Eolis Sensor RTS, wireless wind protection of a retractable awning is possible. If sun protection is also desired, simply use the Soliris Sensor RTS. Two user-defined intermediate positions can be programmed. This control is packaged in a weatherproof enclosure and includes watertight strain-relief fittings for wires entering the box.The receiver can memorize up to 12 different transmitters or channels and up to 3 different sensors.1. The Universal Receiver should be mounted as close to the motor aspossible. If mounted outside, ensure that the connections are facing down to avoid rain seepage. Avoid mounting the control against any metallic surface, as this may affect radio reception.2. Connect high voltage wires according to the wiring diagram on the next page. Make sure to use included watertight strain relieffittings to maintain the weatherproofing of the enclosure. 3. If used, the RTS sensor should be placed close to the awning or shading system to make sure the wind speed or sun intensity is measured at the product. Guard against installing the wind sensor too close to an obstruction such as a chimney, gutter or the windowcovering itself, which could block the wind and cause erroneous sensor readings. The sensor should also not be mounted in the shade or be obstructed by trees, to ensure accurate sunlightreadings. xPROGRAMMING PROCEDURESRECORDING THE INTERMEDIATE POSITION FROM THE TOP OF THE WINDOW TREATMENT- Bring the window treatment to its upper limit using the Telis transmitter. Press the DOWN and MY buttons simultaneously until the awning begins to move, then release. - Stop the window treatment at the intermediate position desired. Press the MY button for 2 seconds to memorize that position.RECORDING THE INTERMEDIATE POSITION FROM THE BOTTOM OF THE WINDOW TREATMENT- Bring the motorized treatment to its lower limit. Press the UP and MY buttons simultaneously until the awning begins to move, then release.- Stop the window treatment at the position desired. Press the MY button for 2 seconds to memorize that position.DELETING AN INTERMEDIATE POSITION- Briefly press the MY button of the Telis transmitter to reach the desired intermediate position. - Continue to press the MY button for 10 seconds until the programming LED on the Centralis Receiver stops blinking. That position is now deleted.TO ADD A NEW TRANSMITTER or SENSOR TO THE MEMORY OF THE RECEIVER- Press the programming button, for more than 2 seconds, on a transmitter that is already memorized by the Universal Receiver to wake up the receiver. The programming LED on the Receiver will blink, and the motor will jog. Press the programming button on the new transmitter or sensor to attach it to the Universal Receiver. The programming LED on the receiver will light and the motor will jog indicating the transmitter or sensor is memorized. TO REMOVE A TRANSMITTER or SENSOR FROM THE MEMORY OF THE RECEIVER- Press the programming button, for more than 2 seconds, on a transmitter that is already memorized by the Universal Receiver to wake up the receiver. The programming LED on the Receiver will blink, and the motor will jog. Press the programming button on the transmitter or sensor you want to remove from memory. the programming LED on the receiver will light and the motor will jog indicating that transmitter or sensor will no longer operate the Universal Receiver. TO REMOVE ALL TRANSMITTERS or SENSORS FROM THE MEMORY OF THE RECEIVER - Press and hold the programming button of the Unviersal Receiver for more than 7 seconds until the LED blinks and the motor jogs twice. This removes ALL memorized transmitters or sensors.REF. NO: 25006270SOMFY SYSTEMS, INCEvery buyer gets a MyStoreRewards invitation for cash back FREE! Sellers: Add a FREE map to your listings. FREE!.