APM Flight Controller Set APM 2.6 & GPS & OSD & Radio Telemetry & Power Module & Shock Absorber

Product Description:
APM 2.6 (with vertical pins) Brand: APM
Compare with APM 2.52: APM 2.6 without welding electronic compass on the main board, the board has no on board compass.
System: Complete open source autopilot system

Product Features:
1. It allows the user to turn any fixed, rotary wing or multi-rotor vehicle (even cars and boats)into a fully autonomous vehicle; capable of performing programmed GPS missions with way-points.
2. This revision of the board has no on board compass, which is designed for vehicles (especially multi-copters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them,too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.
3. APM 2.6 requires a GPS unit and external compass for full autonomy. Choose your compass from options menu at right.
GPS Power supply cable: the default style of APM
Compass: 6M
Terminal outgoing lines: compatible with APM serial port and I2C port
OSD Operating voltage: 5V-12V
Application: DIY flight control projects

Product Features:
1. Perfect combination of ATmega328 and MAX7456.
2. Flight control OS functions
3. Supports MAVLink protocol.
4. Uses MAVLink OSD.

Radio Telemetry 433MHz and 915MHz
Antenna connectors: RP-SMA connector
Output Power: 100mW (20dBm), adjustable between 1-20dBm
Sensitivity: -117dBm sensitivity
Interface: standard TTL UART
Connection status: LED indicators
Country: For Europe

Product Features:
1. Very small size,light weight
2. Receiver sensitivity to -117 dBm
3. Transmit power up to 20dBm (100mW)
4. Transparent serial link
5. Air data rates up to 250kbps
6. Range of approx 1 mile with supplied antennas
7. Demonstrated range of several kilometers with a small omni antenna
8. Can be used with a bi-directional amplifier for even more range
9. MAVLink protocol framing and status reporting
10. Frequency hopping spread spectrum (FHSS)
11. Adaptive time division multiplexing (TDM)
12. Support for LBT and AFA
13. Configurable duty cycle
14. Built in error correcting code (can correct up to 25% data bit errors)
15. Open source firmware
16. AT commands for radio configuration
17. RT commands for remote radio configuration
18. Adaptive flow control when used with APM
19. Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF micro-controller.
Power Module Weight: about 30g
Note: Without BEC. You should solder yourself.

Maximum input voltage 50V, can measure the maximum current is 90 A, realize the control of slabs and the voltage of the battery capacity monitoring. Voltage current detection of Official design parameters, design parameters and 3 ground station (mission planer) can directly refer to the official Wiki Settings.
It is used to test battery voltage and current, flight control board, the two reception battery remaining power calculation, estimate the remaining time of flight.
Shock Absorber Material : Glass fiber
Color: Black
Application: For different flight controllers, such as APM 2.5/2.6, KK, MWC, etc.
Priority Direct Mail 6-9 business U.S. & Australia Orders
Standard Registered Air Shipping 7-20 day delivery U.K. and other destinations.
Package includes all the following:
1 APM2.6
1 GPS
1 OSD
1 Radio Telemetry
1 Power Module
1 Shock Absorber