Silicone oil PMS-200 REXANT, 100 ml

PolyMetilSiloxane fluid PMS-200 (GOST 13032-77) REXANT is a colorless, transparent, chemically inert and corrosion-resistant silicone fluid odorless.
Unlike mineral or synthetic oils, this fluid has excellent electrical insulating, anti-adhesive and anti-foaming properties.

Application area:
Lubrication of rubber seals and processing of high voltage wires.
Basis of low-temperature and high-temperature:
a) greases, pastes and petroleum jelly;
b) motor and transmission oils.
As a release agent (metal-plastic, plastic-rubber, etc.) and mold release agent for molding and extruding plastic products:
a) in the manufacture of rubber and plastic products;
b) in the tire industry;
c) for conveyor belts;
d) in the production of rubber;
e) in the manufacture of plastic products.
Liquid for devices and mechanisms:
a) cooling;
b) depreciation;
c) hydraulic;
d) damping;
e) dielectric;
e) release agent;
g) separation.
As a heat carrier with a temperature range of –100 ... + 300 ° C
As an additive in varnishes and various household cleaning products in:
a) polishing compounds and mastics;
b) polishing compounds for furniture;
c) polishing compounds for automobiles;
d) household chemicals;
d) cosmetics, the basis of sunblock, lipstick and so on;
e) hair care formulations;
g) shoe care products, leather products;
h) mastics for the floor.
Sizing for wool semi-finished products in carding and weaving.
For power transformers, rectifiers, magnetrons, etc., as a cooling and dielectric fluid (including replacement of Sovtol-10).
As a liquid to increase strength and defect-freeness when processing glassware and sterilizing medical instruments.
Antifoam base for:
a) textile industry;
b) drilling fluids of the oil and gas industry;
c) for any processes and production;
d) food industry (stabilizing, antifoam additive E900).
In the textile industry, to soften fabrics made of cotton and synthetics, impart water-repellent and abrasion resistance to technical fabrics.
For the production of various emulsions and additives in the manufacture of paints, sealants, protective and polishing coatings, adhesives, etc.

Thus, the applications of silicone fluids are constantly expanding due to the improvement of production technology and lowering the cost of its production.

Basic properties:
PMS fluids are resistant to high and low temperatures, do not form residues on the treated surfaces, and prevent the adhesion of thermoplastic materials to each other.
Stability of physical properties of PMS liquids in a wide range of operating temperatures, from –40 ... + 200 ° С
Excellent viscosity / temperature characteristics, high compressibility and shear resistance.
PMS fluids give excellent sliding properties and hydrophobicity to plastics and rubbers, reduce friction of surfaces.
The electrical characteristics of PMS fluids are virtually unchanged at high and low temperatures over a wide frequency range.
Form a hydrophobic protective film.
Resistance to radiation.
Low surface tension, strong hydrophobic properties.
Pour point below –60 ° C

Main characteristics:
Kinematic viscosity: 200 cSt
Volume: 100 ml

Norms in accordance with GOST 13032-77
Appearance: colorless transparent liquid
Content of solids: none
Kinematic viscosity at 20 ° С: (192–208). 10-6 / 192–208 m2 / s (cSt)
Kinematic viscosity at –50 ° С, m2 / s (cSt), no more: not determined
Kinematic viscosity at –60 ° С, m2 / s (cSt), no more: not determined
Dynamic viscosity at –50 ° С, no more than: 2000 Pa.s (cP)
Flash point in an open crucible, not lower: 316 ° С
Pour point, not higher: –62 ° С
The reaction of the environment (pH of the aqueous extract): 6.2-7.0
Mass fraction of silicon: 37.0–38.5%
Mass fraction of water, no more: 0,004%.

Safety:
PMS-200 fluid is environmentally friendly, does not cause irritation, allergies, is explosion-proof and non-toxic.